Impact garage doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateTherma-Tru Impact Garage Doors: The Mesquite Owner’s Guide
We install Therma-Tru-compatible impact garage doors and replacement components throughout Mesquite, and most installed door replacements land between $2,400 and $6,800 depending on size, glass package, and how much of the existing framing has to be rebuilt. A like-for-like panel or hardware swap is usually a single-visit job; full door replacement we schedule, measure twice, and fit to your opening rather than to a catalog number.
Owners here tend to find the failure the same way. The door starts binding in July, or the bottom seal leaves a gray streak across the driveway after a windstorm, or a panel face cracks starting at a hinge screw. Mesquite sits in a high-wind exposure area with summer surface temperatures on a west-facing door that will soften cheap seals and stress cheap hinges, so the part that gives first is almost always the one carrying the most load. We’re an independent service provider and not affiliated with Therma-Tru; what we do is match the right part to the door you actually own and install it true.
Which Therma-Tru Models This Applies To
Therma-Tru garage door systems in this market are most commonly the impact-rated lines built around their steel and composite panel faces with laminated or tempered impact glazing, typically in 8-, 9-, and 16-foot widths and 7- or 8-foot heights. The part number you need depends on the series, not the color, and that’s where most homeowners go wrong: two doors that look identical on the driveway can carry different hinge gauges, different bottom seal profiles, and different strut spacing.
Find the manufacturer label first. It’s usually on the inside face of the top section or on the end stile of the bottom panel, and it carries the model, the section profile, and the wind-load rating. Write those down before you call anyone, including us. If the label is painted over or gone, we take three measurements that matter more than the nameplate: the finished opening width and height, the panel thickness, and the hinge center-to-center spacing. That last number tells us which hinge family the door was built around.
The OEM-versus-aftermarket decision is straightforward on Therma-Tru. OEM hinges, rollers, and bottom seals fit the first time, come with the manufacturer’s tolerances, and preserve your wind-load rating documentation. Quality aftermarket equivalents cost less and are fine for rollers and seals, but we don’t put aftermarket hinges on an impact-rated door unless the gauge and screw pattern match the OEM spec exactly, because the rating certificate was tested with the specific hardware. Side-by-side, on paper, with the difference stated: that’s how we quote manufacturer lines in Mesquite.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your Therma-Tru Impact Garage Doors Are Failing
- The door binds or drags in hot weather. Steel and composite panels expand against a tighter opening as temperatures climb past 105°F, and a hinge that’s worn a few thousandths will show up as a scrape near the middle of the track. If it only binds in summer, it’s usually hardware wear, not a track problem.
- Gray or black streaks under the bottom seal. The seal is breaking down and leaving residue on the concrete. On an impact door the bottom seal also carries part of the wind seal, so a hardened or cracked seal is a rating issue, not just a cosmetic one.
- Cracks radiating from hinge screws or panel edges. Repeated wind cycling fatigues the metal around fasteners. A hairline crack at a hinge is a panel replacement conversation; ignoring it lets water into the core.
- The door no longer seals evenly at the header or jambs. Weatherstripping that’s hardened in the desert sun stops compressing. You’ll see daylight at the top corners before you feel a draft, and dust finds it first.
- The opener strains or reverses on the way down. That’s often a door balance problem from a worn roller or hinge, not an opener problem. Replacing the opener before the hardware wastes money and hides the real cause.
If the door is a torsion-spring or high-tension cable system, stop here. Those components are under extreme load and are genuinely dangerous to touch; a spring that lets go can cause serious injury. We’re not going to walk you through adjusting one, and no honest tradesperson will either. Call a trained technician.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Mesquite runs roughly like this, and these are ranges, not a fixed bid until we’ve measured:
- Bottom seal replacement, OEM profile: $120 to $280 installed.
- Hinge and roller set, impact-rated, full door: $340 to $720 installed.
- Weatherstripping, header and jambs: $180 to $420 installed.
- Single panel replacement, impact-rated: $460 to $1,100 installed, depending on section and glazing.
- Full impact door replacement, Therma-Tru-compatible: $2,400 to $6,800 installed.
What drives the range is glazing type, door width, whether the framing is plumb and square, and whether the wind-load documentation has to be re-established. Every quote is line-item on paper: part, labor, disposal, and any framing repair called out separately so nothing shows up on the final bill that wasn’t on the first one. Most jobs are done in a single visit. Our workmanship carries the 90-Day Done Right Promise – if it’s not done right, we make it right, with no paperwork fight – and under The Keystone Standard we register both manufacturer warranty layers in writing before we leave.
DIY or Call Us?
Here’s the honest split. You can safely check the label on the inside of the top section, measure your opening, and look for daylight at the corners. You can vacuum grit out of the track and wipe it down. You can tighten a visibly loose hinge screw with a screwdriver, gently, once.
Where it goes wrong: adjusting torsion springs or cables (dangerous, no exceptions), swapping hinges on an impact-rated door without matching the gauge and screw pattern (voids your rating documentation), and forcing a binding door with the opener (cracks panels and burns out the motor). The part is rarely the whole problem. An out-of-true opening is what wore the part out in the first place, and on a Mesquite door, sun and wind find that every time. Call us at (833) 620-7092 and we’ll measure it properly.
FAQs
Seals and weatherstripping in this climate typically give out in 5 to 8 years, rollers and hinges in 8 to 12, and panels hold far longer unless they’re cracked or water has gotten into the core. The desert sun is harder on seals than the wind is, and a west-facing door will age faster than a shaded one.
Sometimes, yes. A single worn roller or a loose hinge can often be replaced without touching the rest of the door, and a seal that’s only failed at one end can be re-set. Once a panel is cracked, or the hinge screw holes are stripped, replacement is the honest answer.
A seal or hardware set is usually done in one visit of a couple of hours. A panel replacement is a half day. A full door replacement we schedule and complete in a single visit once the door is on site, and we confirm the date and time in writing.
We match your label and measurements to the correct OEM part or an approved equivalent, then quote it to you on paper before ordering. We don’t claim to stock parts or carry them on a truck; we order the right one for your door, which is why the label and the three measurements matter. We also service PGT, CGI, and CWS impact products.
Call (833) 620-7092 for a free estimate. A live person answers 24 hours a day, 7 days a week. TruePane Windows & Doors Mesquite has served local communities for over 42 years, and our technicians have up to 18 years of experience. Seniors and veterans get a permanent 5% discount, and we’re running $50 off any repair over $250 and an $89 seasonal tune-up.
Written by the team at TruePane Windows & Doors Mesquite, serving Mesquite and nearby areas.