Sliding glass doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCWS Sliding & Patio Doors: The Mesquite Owner’s Guide
We replace and service CWS sliding and patio doors for Mesquite homeowners, and most complete door replacements land between $1,800 and $4,600 installed depending on size, glass package, and whether the frame is sound. If just the rollers or the lock have gone, expect a repair visit rather than a replacement, usually $150 to $400. TruePane Windows & Doors Mesquite is an independent service provider and is not affiliated with CWS.
Owners rarely call us about a part. They call because a door that slid fine for fifteen years suddenly needs a shoulder to move, or because a Mesquite windstorm pushed grit into a track and the panel jumped its rail. By the time someone picks up the phone, the symptom usually points to one of four parts: rollers, track, weather seal, or the glass unit itself. This page is written to help you name the failing part before we arrive, so the estimate is a conversation about a fix rather than a guess.
Which CWS Models This Applies To
CWS built slider and patio doors across several product lines, and the parts do not swap freely between them. The identifying mark is a label on the door frame or the glass edge, usually a small silver sticker with the series name and a manufacturing date. If the label has weathered off in the desert sun, photograph the roller housing at the bottom corner of the sliding panel and the lock strike plate; we can often match a series from those two images alone.
The compatibility gotcha we see most often in Mesquite is roller height. CWS sliders were built with several different roller assemblies, and the wheel diameter and housing height differ by as much as a quarter inch between series. A homeowner who buys rollers by photo from an online listing, without measuring the housing, ends up with a panel that sits 3/16″ low and drags the sill plate. Measure the housing height and the existing wheel diameter before you buy anything.
On the OEM-versus-aftermarket question, our answer for CWS specifically is that a quality aftermarket roller in stainless housing often outlasts the original part, because the original was built to a price and the modern stainless equivalents hold up better to the grit that blows through the Mesquite Valley. Where we insist on OEM or an exact equivalent is the lock, the handle, and the weather seal profile, because those are where a near-match shows.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your CWS Sliding & Patio Doors Is Failing
These five symptoms cover most of what we’re called out to look at. Each one points to a specific part.
- The panel drags or needs a shoulder to open. Worn or flat-spotted rollers are the usual cause, and grit in the track accelerates the wear. In Mesquite, a door facing the open desert takes on more abrasive dust in one season than a sheltered door does in three.
- Visible grooves or a shiny worn strip in the track. Aluminum tracks wear thin under steel rollers, and once the anodized surface is through, the soft metal underneath grinds down faster. A worn track eats new rollers within a year unless the track is sleeved or replaced.
- Daylight or a draft at the edges when the door is closed. The weather seal, or the pile strip in the jamb, has flattened or pulled loose. This is the one most owners miss until the summer power bill tells them.
- Fog or condensation between the panes. The insulated glass unit has lost its seal, and the desiccant is saturated. No amount of wiping fixes this; the glass unit has to be replaced.
- The lock no longer catches, or the handle is loose. The strike plate has shifted with the door dropping on its worn rollers, or the mortise lock has worn internally. It’s often a symptom of the roller problem, not a lock problem on its own.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Pricing in Mesquite depends on size, glass package, and whether the existing frame is reusable. Here is the range we quote:
| Work | Installed Range |
|---|---|
| Roller and track repair, one panel | $150 – $400 |
| Weather seal replacement, full perimeter | $120 – $280 |
| Insulated glass unit replacement, one panel | $400 – $900 |
| Full slider replacement, standard size, frame sound | $1,800 – $3,200 |
| Full slider replacement, large or custom size | $3,200 – $4,600 |
Those numbers include parts and labor. They don’t include frame repair if the sill is rotted or the header is out of level, and we’ll flag that in writing before work starts, not as a surprise on the bill. Most repair jobs are finished in a single visit. Replacements take more, but you get a written line-item quote before we order anything, and the work is covered by our 90-Day Done Right Promise and The Keystone Standard: warranty layers registered in writing, durations stated, before the truck leaves the driveway.
DIY or Call Us?
There’s no genuine safety hazard in a CWS slider the way there is with a garage door spring or an electrical panel. That said, the panels themselves are heavy and awkward, and a dropped glass panel is expensive. If you want a real answer on what’s safe to try: you can safely clean the track, inspect the rollers with a flashlight, check the seal for gaps, and test the lock alignment. What goes wrong when owners go further is the roller swap. That’s where the wrong housing height is discovered halfway through the job, or where a panel is lifted out and set down on a corner that wasn’t reinforced. Call (833) 620-7092 and we’ll tell you over the phone whether your symptom is a repair or a replacement.
FAQs
Five to twelve years is the honest range in Mesquite, and the shorter end applies to doors facing open desert. The grit that blows through here is more abrasive than what rollers face in a sheltered lot, so we see roller failures earlier than the manufacturer’s spec sheet suggests. Call (833) 620-7092 for an exact look at yours; estimates are free.
Yes, and often it should be. Rollers, tracks, seals, and locks are all serviceable on most CWS sliders, and a repair that costs $300 today can buy you another several years from a sound door. We only recommend replacement when the frame is rotted, the glass is failing across multiple panels, or the door is out of square. Call (833) 620-7092 and we’ll give you both numbers so you can decide.
A roller replacement on one panel is typically a single visit of one to two hours, and a track resleeve alongside it takes another hour or so. Larger jobs sometimes run into a second visit if a part has to be ordered to match your series. Call (833) 620-7092 to schedule.
We identify your series from the door frame label or from photos of the roller housing and lock, then source from authorized CWS parts channels or from a quality aftermarket equivalent we’ve tested. We don’t carry a stock of CWS parts, so expect a short lead time on some series. Call (833) 620-7092 with your door’s information and we’ll tell you what’s available.
We also service sliding and patio doors from PGT, CGI, and ES Windows.
If your CWS slider has started dragging, sealing badly, or fogging, call TruePane Windows & Doors Mesquite at (833) 620-7092 for a free estimate. A live person answers every call, 24 hours a day, 7 days a week. Our technicians have up to 18 years of experience, measure every opening twice, and put the quote on paper before any work begins. If the pane is not true, the job is not done.
Written by the team at TruePane Windows & Doors Mesquite, serving Mesquite and nearby areas.