Sliding glass doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCGI Sliding & Patio Doors: The Mesquite Owner’s Guide
We install and service CGI sliding and patio doors throughout Mesquite, and a full door replacement typically runs $2,400 to $5,800 installed, depending on size, glass package, and whether the opening needs reframing. A roller, track, or glass swap on an existing CGI panel is a smaller job, often $220 to $650 in parts and labor. Most owners find us the same way: the door starts dragging in July, the latch stops meeting the strike, or the glass on the fixed panel fogs from the inside. Those three symptoms tell you most of what you need to know before anyone touches the door.
Which CGI Models This Applies To
CGI makes several sliding and patio lines, and the parts are not interchangeable between them. The most common residential series we see in Mesquite are the CGI vinyl sliders and the heavier impact-rated sliders that went into homes built or re-glazed after the county tightened its windborne-debris requirements. Before we quote anything, we find the manufacturer’s label, usually on the top or side of the operating panel’s frame or etched into the glass corner. That label gives us the series and the glass code. From there, we measure the panel height, width, and the existing roller track depth, because a CGI slider built for a 1 1/4-inch track will not sit right on a 7/8-inch track, and we’ve seen that mismatch cause a door to bind within weeks of a bad swap.
On the OEM-versus-aftermarket question, we’ll tell you plainly: for rollers and weatherstripping, a quality aftermarket equivalent from a known supplier often outperforms the original and costs less, because roller hardware has improved since many of these doors were made. For glass, latches, and impact-rated components, we stick with OEM or OEM-spec parts so the door keeps the rating it was built to. CGI is one of more than a dozen lines we install and service, alongside PGT, CWS, and ES Windows, and we quote the options side by side on paper so you see what you’re buying. We’re an independent service provider, not affiliated with CGI.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your CGI Sliding & Patio Doors Is Failing
These are the failures we get called about most in Mesquite, and each one points to a specific cause:
- The door drags or scrapes near the bottom. Worn steel rollers or a flattened track, usually accelerated by fine desert grit that works into the track and grinds the roller wheel down. In Mesquite, we see this sooner on doors facing open lot lines or the wash, where dust settles fast.
- The glass fogs or shows a haze between the panes. A failed seal in the insulated glass unit. Once the seal goes, the unit is done; no amount of cleaning brings it back, and Mesquite’s summer heat cycles speed that seal failure along.
- The latch won’t catch or the door rides up out of the strike. Rollers out of adjustment or worn, which changes the door’s height in the frame. It’s a hardware problem, not a lock problem.
- Water pooling on the interior sill after a storm. Failed weatherstripping, a blocked weep hole, or a door that has settled out of square. Any of the three lets wind-driven rain past the seal.
- The door feels loose in the frame or rattles in wind. Worn rollers plus a track that’s pulled away from the sill, often after years of expansion and contraction. Left alone, it puts stress on the frame and the glass.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what these jobs run in Mesquite, parts and labor together, quoted upfront with no surprise line items:
- Roller replacement, both panels: typically $220 to $380
- Track repair or replacement: typically $280 to $520
- Insulated glass unit (one panel): typically $420 to $780
- Latch, strike, and weatherstripping: typically $180 to $340
- Full sliding door replacement, standard size: $2,400 to $4,200
- Full impact-rated replacement: $3,600 to $5,800
What drives the range: panel size, glass package, impact rating, and whether the opening is plumb and square. We measure every opening twice and give you a written line-item quote, so parts and labor are broken out and you see exactly where the money goes. Every job is backed by our 90-Day Done Right Promise, and both manufacturer warranty layers are registered in writing before we leave. Most repairs are completed in a single visit.
DIY or Call Us?
Some checks are safe and worth doing yourself. Clean the track, work the door back and forth to confirm where it drags, look for the label so you know the series, and check that the weep holes on the exterior sill are open. That takes ten minutes and tells you a lot.
Where it goes wrong is the part that carries weight. Sliding patio door panels are heavy, and tempered or laminated glass can run well over a hundred pounds. Lifting a panel out to swap rollers without a second set of hands and the right technique risks the panel dropping, cracking the glass, or injuring your back. Adjusting rollers wrong can warp the frame or crack a pane. Reframing an out-of-square opening is beyond a homeowner job. This is real safety, not scare tactics: if the panel is heavy or the glass is impact-rated, let a technician handle it. Our technicians have up to 18 years of experience, are background-checked and uniformed, and measure twice before quoting. Call (833) 620-7092 and we’ll walk you through what your door likely needs.
FAQs
Rollers typically last 10 to 15 years in our climate, and insulated glass seals often go 12 to 20 years before fogging. Mesquite’s heat and dust are hard on both: the summer temperature swings stress glass seals, and airborne grit wears rollers faster than in milder, greener climates. When a part reaches that age, replacement is usually the honest answer. Call (833) 620-7092 for a free estimate on yours.
Often, yes. Rollers, latches, tracks, and weatherstripping are all replaceable on their own, and a repair is the right call when the frame and glass are sound. A fogged insulated glass unit is the exception: once the seal fails the unit has to be replaced, not repaired. We’ll tell you which one you’re facing. Call (833) 620-7092 for an exact quote, free of charge.
Most roller, track, and hardware swaps are done in a single visit, usually a couple of hours. A glass unit replacement is similar. A full door replacement is a longer appointment, and we’ll give you the window in writing when we quote. We’ll be there when we say. Call (833) 620-7092 to schedule.
We match the part to your door’s series and the measurements we take on site, and we quote OEM or a quality aftermarket equivalent, whichever is the better fit for that component. We confirm the exact part before ordering, so you’re not paying for a guess. Call (833) 620-7092 and we’ll get your CGI door measured and quoted.
When a CGI door stops doing its job, the fix usually comes down to matching the right part to the right series and setting it true. That’s the work we do across Mesquite, and it’s backed by The Keystone Standard and a square deal on pricing. A live person answers our phone around the clock, so call (833) 620-7092 for a free estimate and let’s get your door closing the way it should.
Written by the team at TruePane Windows & Doors Mesquite, serving Mesquite and nearby areas.